Happy New Year!

Look at these incredible rainbows I saw yesterday in South Philadelphia. May they be a harbinger of the year to come.

Happy Holidays

A Christmas Eve post this year.

Some pictures from around my neighborhood.

IMG_3581

 

IMG_3610

 

IMG_3604
Isgro’s Pastries.  A South Philadelphia institution.  Cranking out the cannolis since 1904!

And back by popular demand, guest blogger Boris tells the story of how the Tabby got its “M”.

 

 

Still on Hold

I wrote a few weeks ago about how my basement studio was in a state of upheaval due to the installation of New Gizmo in the back part of the basement.   Since New Gizmo replaced the  boiler and hot water heater,  does not use the chimney for ventilation,   I decided to move my kiln and polymer convection oven to the back basement and install a ventilation system using the chimney.  I already have a ventilation system in the front basement that I installed for soldering but which I found worked beautifully when I was cooking polymer and firing bronze clay.  Read more about that one here.

I still haven’t decided whether to install a downdraft vent for the kiln or to go with a hooded vent that I can use for the kiln and the convection oven.   I already made a plenum cup that fits into the kiln’s rolling stand  right under the kiln, but I have hesitated to drill the small hole in the bottom of the kiln that the downdraft vent would need to function.  If I made a downdraft vent for the kiln,  I would have to be able to detach it from the inline fan and connect separate ductwork to hood to ventilate while the convection oven is operating.      I think I am going to set up hooded vent first and see how it does before I make the final decision.

1inlinefan

Here’s the inline fan I ordered from Amazon.  It’s the same one I have in the front basement.  It’s not too loud, has a variable speed controller, and does not require any special wiring.   I will have to bolt it to a piece of wood to steady it.   I could bolt it from the ceiling, too.    I will need two 4″ to 6″ vent reducer/increasers to connect each side of the fan to the ductwork.  I also ordered them from Amazon.   One will connect to ductwork that hooks into the  4″ chimney opening behind the fan and the other one will connect on the other side of the fan to a longer section of ductwork and the vent hood.

My electrician installed an extra outlet  for the fan and the convection oven.   The Paragon Max 119 kiln runs on 120 volts but does require some additional wiring and a special outlet which Stubewan the electrician also installed.   He also left me some metal tape and ductwork to use.  Thanks, Stu!

I used a wok lid for the vent hood in the front basement.  I will use a stainless steel mixing bowl for the vent hood in the rear basement.

BowlHood
Bought at a house sale for $5.00.  I will saw out a hole in the top and  attach the ductwork.

At this point, I plan to attach the ductwork and hood to the wood beams in my basement ceiling and raise and lower the hood with a chain.

 

 

I plan to stow the kiln under the stairs and move it out to the middle of the floor for firing.   I was hoping to get it all hooked up this week, but Amazon sent the wrong size reducers.  Back they go and new ones ordered.

Wish me luck!

Greek Tragedy

I went to the hand doctor today. I can’t believe it’s been more than two months since they rebuilt my thumb joint. I am progressing nicely and should be back to throwing pots by February. Which is good because I pretty much sold all of the pottery I brought to Handmade for the Holidays, and a nice amount of the jewelry too.

So I haven’t been doing too much making lately. I am hoping that will change soon.

I leave you with a story.

I walked into the living room where my husband was watching a movie called Troy the Odyssey. I noticed the cheap vinyl piping on the actors’ costumes that was supposed to pass for Greek warrior gear. I commented that it must not be a very good movie.

My husband replied that the movie was so tragically bad that it could only have been written by Sophocles.

“Sophocles?” I asked, Didn’t he write plays? ”

“He wrote Oedipus,” my husband responded.

“And Antigone,” I added, remembering my Greek tragedies.

“He did write Antigone,” my husband informed me. And the great tragedy there was that she never wrote back.”

Handmade for the Holidays

This is where I’ll be selling my wares this weekend along with the other potters who share studio space at Fleisher Art Memorial.
Screen Shot 2019-11-27 at 2.56.19 PM
GroupHFH
Screen Shot 2019-11-27 at 2.47.52 PM

I’ll have more than pottery.  I will also be selling jewelry made from recycled materials and ceramics, bronze, and fused glass.

See you there!